Tendering and estimating, 17 November 2026

AI tendering for building services contractors (plumbing, heating, air con, mechanical)

AI tendering for building services contractors means software reads plant schedules against the drawings and works out who carries the design. Installing to a consultant's design, taking a contractor's design portion and full design and build carry different risk, and the price should change with them. You still own sizing, commissioning, lead times and F gas compliance.

Who designs it, and why does that change the price?

Because whoever designs it pays when it doesn't work. Building services packages come in three forms, and the pack doesn't always say which one you're in.

  • Install to design. A consultant has designed the system. You price the drawings and schedules, install what they show, and raise questions where they conflict. If the boilers are too small, that's the designer's problem.
  • Contractor's design portion. The consultant designs most of it and hands you one part to design, often the cooling, the controls or the above-ground drainage, against a performance specification. You own that part.
  • Full design and build. You get a brief or a performance specification and design the lot: heat loss, plant selection, pipe sizing, controls and compliance.

Look for words like "performance specification", "contractor to size", "contractor's design portion", "design responsibility matrix" and "indicative layout". Any of them means design work, and design needs time, insurance and a different price.

The same office tendered three ways

Here is one small office priced under each route. It is a two-storey, 450 m² building with two condensing boilers, radiators, hot and cold water to the toilets, and cooling from six ceiling cassettes on three outdoor units. The install cost is the same in all three. What changes is design time and risk.

Install to designContractor's design portion (cooling and controls)Full design and build
Install cost: labour, materials, plant£86,000£86,000£86,000
Design time at £450 a day£06 days: £2,70014 days: £6,300
Design risk allowance£03% of £24,000 cooling plant: £7205% of £86,000: £4,300
Total cost£86,000£89,420£96,600
Price at a 12% margin (cost ÷ 0.88)£97,727£101,614£109,773
Who pays if the cooling is undersizedThe client's designerYouYou
What you must check before pricingDrawings against schedulesThe performance spec and your insuranceThe brief, compliance, and every calculation

All figures are illustrative. Use your own day rates and decide your own risk allowance.

Three points come out of this. First, the design and build price is about £12,000 higher than the install price for the same pipes and plant, and a client who compares only totals may not see why. Say what the extra buys: design, calculations and the risk. Second, on the contractor's design portion the risk sits in one part, so put the allowance against that part instead of spreading it across the job. Third, if your price is the same under every route, you have priced design for free.

AI helps most on the install-to-design route, where the work is reading and matching. On design and build, it can read the brief and list what you need to calculate, but the calculations and the sign-off are yours. Before you lean on its numbers, test AI on a tender you have already priced.

What does commissioning involve, and how should you price it?

More days than most tenders allow. Commissioning a small office covers filling and venting, flushing and water treatment, balancing the heating, setting up the boilers and controls, commissioning the air con, witnessing for the client and producing the O&M manual. Price it as a line of its own, in days, with the documents as a separate line.

Worked example

Commissioning line for the 450 m² office

Two boilers, 28 radiators, hot and cold water, three air con systems.

Fill, vent, flush and dose the heating system2 people × 1 day × £260£520
Boiler commissioning and controls set-up1 day × £260£260
Balance 28 radiators and record flow temperatures1 day × £260£260
Commission three air con systems2 people × 1 day × £260£520
Witness visit with the client's engineer2 people × half a day × £260£260
Water treatment chemicals and flushing kitallowance£280
O&M manual, certificates and records1.5 office days × £220£330
Commissioning and handover line7 site days, 1.5 office days£2,430
Day costs, durations and the chemicals allowance are illustrative. A second witness visit adds another £260.

Handover information matters to the client for years. GOV.UK guidance says air conditioning systems with an effective rated output above 12kW must be inspected by an energy assessor at least every five years in England and Wales, with the first inspection within five years of the system going into service. Six cassettes on three outdoor units can pass that figure, so the client will want the system details in your O&M manual. Raise it in your return so the information is priced and planned.

How should long-lead plant sit in a tender?

As a named risk with a date on it. Boilers, outdoor units, heat pumps and controls can have lead times that don't fit the main contractor's programme, and prices can move between tender and order.

Get a written lead time and a price validity date from the supplier for each major item, and put both in your return: "plant prices valid for 30 days from tender; programme assumes order placed by [date]". If the main contractor wants plant on site early, ask who pays for storage and insurance. If the client wants a specific brand, ask whether an equal is acceptable and price the named one.

What do F gas and planning add to an air con tender?

Certification costs and, sometimes, a planning delay. Both belong in the tender before you are appointed.

If you subcontract the air con on a mechanical package, ask for the subcontractor's company certificate at tender stage. Our guide to F gas certification for air conditioning covers the categories.

Planning is the other check. The Planning Portal says air conditioning at a home can be permitted development only if the system provides heating, so cooling-only units need a planning application, and listed buildings and conservation areas need consent or permission. On commercial jobs, the outdoor units may need planning too, especially on a roof or near neighbours. If the pack doesn't say planning is in place for external units, qualify it. Our guide to air conditioning and planning permission has more.

What can AI check in a building services pack?

Schedules against drawings, which is slow, tedious and where errors hide. A plant schedule lists every boiler, cassette, pump and valve set with its reference, duty and size. The drawings show where each one goes. AI reads both and flags every mismatch.

Cross-checks to run on a building services pack

The Swindon owner of a plumbing, heating and air conditioning firm with about six engineers had a weekend's worth of the same problem in a smaller form:

4–5 hours per air con quotenowabout 20–25 minutes

I've got 22 aircon quotes to do this weekend… I'll be here all weekend.
Owner, plumbing, heating and air conditioning firm, about 6 engineers · Swindon

The time came out of reading and matching: the survey notes, the unit selection and the supplier price. The engineering judgement on unit size stayed with him.

Where does each building services trade go wrong?

Each one tends to lose money somewhere different.

AI tendering for plumbing and heating engineers

Plumbing and heating firms most often miss that "contractor to size" in a spec has made them the designer, and price commissioning and water treatment as an afterthought. AI helps by reading the spec for design wording and matching radiators, valves and plant to the drawings. It can't do your heat loss calculation or tell you the existing pipework is sound. More on heating work at our gas and heating page.

AI tendering for air conditioning installers

Air con installers get caught by planning for outdoor units, by long-lead plant, and by cassette duties that don't match the room loads. AI checks indoor and outdoor units against the schedule and flags duty mismatches. Unit selection, F gas certification and the site survey stay with you.

AI tendering for mechanical and HVAC contractors

Mechanical contractors most often carry design risk on a contractor's design portion without pricing it, and under-price commissioning and witnessing. AI can list every design duty, schedule every item of plant and count fittings. The design, the insurance cover for it and the commissioning plan are yours. See our mechanical and electrical page, and for fixed-price term servicing work, AI tendering for term and maintenance contracts.

Where Nexley fits

Nexley is the AI back office for UK trade firms: five AI assistants run your tenders, quotes, buying, scheduling and invoicing. It connects to the tools you already work in, you run it all from WhatsApp, and you approve everything.

For building services tenders, Nexley reads the specification for design duties, matches the plant schedule against every drawing, counts units and fittings and drafts your price from your own rates, with your qualifications on design, plant and commissioning. You check and approve it on WhatsApp before it goes. The guide to AI tendering by trade covers other packages.

Common questions

What is AI tendering for building services contractors?

It's using AI to read a plumbing, heating, air con or mechanical tender pack, find the design responsibility, check plant schedules against drawings, count fittings and draft a priced return. The contractor still decides the design, the risk allowance and the final price.

Can AI price a building services tender on its own?

No. It can count and match and apply your rates. It can't size plant, judge existing services on site, or decide how much design risk to carry.

What is a contractor's design portion?

It's a part of the works that the contractor designs, usually against a performance specification, while the rest is designed by the client's team. You are responsible for that part's design, so price the design time and check your insurance covers it.

Do I need F gas certification to subcontract air con work?

If your company only manages the work and another company does it, GOV.UK says the company doing the work must be certified. If your own engineers install or service the equipment, your company needs certification too.

Sources

  1. GOV.UK: Company certification to work with F gas
  2. GOV.UK: Qualifications to work with F gas
  3. GOV.UK: A guide to air conditioning inspections in buildings
  4. Planning Portal: Do I need planning permission to add air conditioning to my home?

Every rule, rate and date above was checked against these sources on the date shown at the top.

Topic: Tendering and estimating

Keep reading

Tendering and estimating

AI tendering for groundworks, drainage and surfacing contractors

A ground risk ledger that sorts every risk into price, qualify or reject, one table of the quantity conversions that cost groundworkers money, and a muck-away example at the 2026 Landfill Tax rates.

15 Nov 2026, 16 min read, Kade Dillon

Tendering and estimating

Let down by your bid writer? Fix this first

Why tenders lose even with a bid writer, five things to fix in what you give them, and when drafting in-house with Nexley is the better step.

15 Nov 2026, 5 min read, Kade Dillon

Tendering and estimating

Is AI tendering accurate? How to test it on your own tender

The only accuracy figure that counts is the one from your own drawings. This guide gives you a seven-step test, a worked comparison on a £64,000 package, a quick check for which differences matter and a test sheet to copy.

12 Nov 2026, 10 min read, Kade Dillon

Try it on your own jobs

7 days free, then £799 a month. No contract.

Runs in WhatsApp Set up on a 20-minute call Cancel anytime
I had a quick demo and we’ve never looked back. Nexley works, it’s simple, and we’re really happy. Just give it a try.”
— Pete Charley

Book a demo with Kade

A 20-minute call. Pick a time that suits and he’ll show you Nexley on your own work.

WhatsApp Us